Directory of image this file is from
This file as a plain text file

$60 RL DISK TEST SELECTION MENUS


        RL8A DISK TESTS
        ---------------

        SYSTEM SELECTED: #1

        SELECT ONE:

        TYPE:
                1 -  RL01 PERFORMANCE EXERCISER.                 (AJRLEC)
                2 -  RL01 DRIVE COMPATIBILITY TEST.              (AJRLDA)
                3 -  RL01 DRIVE PART 1 -
                          CONTROLLER TEST                        (AJRLBC)
                4 -  RL01 DRIVE PART 2 -
                          READ WRITE CONTROLLER.                 (AJRLCA)
                5 -  RL01 PACK VERIFIER TEST.                    (AJRLGA)
                6 -  DISKLESS CONTROLLER TEST.                   (AJRLAC)

                R -  TO RETURN TO THE TEST CATEGORY SELECTION MENU.



&123456R% END OF MENU 60
#1
WS78
WS100 OR WS102
WS81, WS82, WS211, WS212, OR WS202
WS200
$62 STARTUP MENU FOR RL8A TESTS


        RL8A DISK TESTS

        SYSTEM SELECTED: #1

        TEST SELECTED: #6

        TO START THIS TEST YOU MUST FIRST REPLACE THE DIAGNOSTIC DISKETTE
        IN THE FLOPPY  DRIVE WITH THE RL8A  DIAGNOSTIC  DISKETTE.   AFTER
        THIS HAS BEEN DONE,  YOU MAY PRESS THE <RETURN>  KEY,  WHICH WILL 
        CAUSE  THE TEST TO BE LOADED  AND  STARTED  AUTOMATICALLY.  AFTER 
        STARTING  THE  TEST,  YOU  MAY  RETURN  TO  THE  SET-UP  MENUS BY 
        RE-BOOTING THE PROCESSOR WITH THE ORIGINAL SYSTEM DISKETTE.

    ********************************************************************
    * TO START: REPLACE SYSTEM DISKETTE WITH RL8A DIAGNOSTIC DISKETTE. * 
    ********************************************************************

        >TO START THE TEST, PRESS <RETURN>.
        >TO RETURN TO THE TEST CATEGORY SELECTION MENU, TYPE "R".


&
R% END OF MENU 62
#1
WS78
WS100 OR WS102
WS81, WS82, WS211, WS212, OR WS202
WS200
#6 OPT4 + OPT5 => OPT6
RL01 PERFORMANCE EXERCISER.     (AJRLEC)
RL01 DRIVE COMPATIBILITY TEST.  (AJRLDA)
RL01 DRIVE TEST PART 1.         (AJRLBC)
RL01 DRIVE TEST PART 2.         (AJRLCA)
RL01 PACK VERIFIER TEST.        (AJRLGA)
DISKLESS CONTROLLER TEST.       (AJRLAC)
$70  SLE TEST DEVICE CODE SELECT



        SERIAL LINE UNIT (SLU) TEST                (AIKLAD)
        ---------------------------                --------

        SYSTEM SELECTED: #1

        SELECT THE DEVICE CODE OF THE KL8A TO BE TESTED:

        TYPE:
                1 -  DEVICE CODE 40/41 (TERMINALS 2, 3, AND 4)

                2 -  DEVICE CODE 44/45 (COMM OPTION WX200AB)

                3 -  DEVICE CODE 46/47 (COMM OPTION WX200AB)

                R -  TO RETURN TO THE TEST CATEGORY SELECTION MENU.


&1123R% END OF MENU 70
#1
WS78
WS100 OR WS102
WS81, WS82, WS211, WS212, OR WS202
WS200
$71 SUBTEST SELECTION


        SERIAL LINE UNIT (SLU) TEST
        ---------------------------

        SYSTEM SELECTED: #1

        DEVICE CODE SELECTED: #6

        SELECT THE TEST DESIRED:

        TYPE:
                1 -  FOR THE INTERNAL LOGIC/DATA TEST.  THIS TESTS
                     THE KL8A MODULE BUT NOT THE INPUT AND  OUTPUT
                     DRIVERS.

                2 -  FOR THE LOOP-BACK TEST.  THIS IS A FUNCTIONAL
                     TEST OF THE KL8A, THE H326 DISTRIBUTION PANEL
                     AND THE INTERCONNECTION CABLES.

                R - TO RETURN TO THE TEST CATEGORY SELECTION MENU.


&12R% END OF MENU 71
#1
WS78
WS100 OR WS102
WS81, WS82, WS211, WS212, OR WS202
WS200
#6
40/41
42/43
44/45
46/47
$72 STARTUP MENU FOR SLU TESTS - LOGIC TEST


        SERIAL LINE UNIT (SLU) - INTERNAL LOGIC/DATA TEST
        -------------------------------------------------

        SYSTEM SELECTED: #1

        DEVICE CODE SELECTED: #6


        ALL TERMINALS CONNECTED TO THE KL8A UNDER TEST MUST BE TURNED OFF.
        IF  A  SERIAL  PRINTER  IS  CONNECTED  TO  THE  KL8A,  IT  MUST BE
        DISCONNECTED.  ALL LINES MUST BE SET TO 9600 BAUD.   THE LOOP-BACK
        SWITCHES MUST BE IN THE NORMAL (OFF) POSITION.

        WHEN THE TEST IS RUNNING,  THE FLOPPY DRIVES WILL CLICK FREQUENTLY
        AND AN END OF PASS MESSAGE SHOULD APPEAR ABOUT EVERY MINUTE.

        STOP THE TEST BY TYPING A CTRL-C.

        >PRESS <RETURN> TO START THE TEST.
        >TYPE "R" TO RETURN TO THE TEST CATEGORY SELECTION MENU.
&
R% END OF MENU 72
#1
WS78
WS100 OR WS102
WS81, WS82, WS211, WS212, OR WS202
WS200
#6
40/41
42/43
44/45
46/47
$73 STARTUP MENU FOR SLU TESTS - LOOP-BACK TEST


        SERIAL LINE UNIT (SLU) - LOOP-BACK TEST
        ---------------------------------------

        SYSTEM SELECTED: #1

        DEVICE CODE SELECTED: #6

        MAKE CERTAIN THAT THE LOOP-BACK SWITCHES ON THE H326 DISTRIBUTION
        PANEL ARE SET ON.  THESE ARE SWITCHES 1 THROUGH 4 OF EITHER S2 OR
        S4,  DEPENDING  ON  WHICH  KL8-A IS BEING TESTED.   ALL TERMINALS
        CONNECTED TO THE KL8-A UNDER TEST MUST BE TURNED OFF. IF A SERIAL
        PRINTER IS CONNECTED TO THIS KL8-A, IT MUST BE DISCONNECTED.  ALL
        LINES MUST BE SET TO 9600 BAUD.

        WHEN THE TEST IS RUNNING, AN END OF PASS MESSAGE SHOULD APPEAR
        ABOUT ONCE PER MINUTE.

        STOP THE TEST BY TYPING A CTRL-C.

        >PRESS <RETURN> TO START THE TEST.
        >TYPE "R" TO RETURN TO THE TEST CATEGORY SELECTION MENU.
&
R% END OF MENU 73
#1
WS78
WS100 OR WS102
WS81, WS82, WS211, WS212, OR WS202
WS200
#6
40/41
42/43
44/45
46/47
$74 END OF SLU TEST MENU



        SERIAL LINE UNIT (SLU) TEST
        ---------------------------


        SYSTEM SELECTED: #1

        DEVICE CODE SELECTED: #6

        TEST SELECTED: #7 TEST


        END OF TEST.




        >PRESS <RETURN> TO RETURN TO THE TEST CATEGORY SELECTION MENU.



&
% END OF MENU 73
#1
WS78
WS100 OR WS102
WS81, WS82, WS211, WS212, OR WS202
WS200
#6
40/41
42/43
44/45
46/47
#7
INTERNAL LOGIC/DATA
LOOP-BACK
$&


$